CNC Machined to Order & Design By NPC and manufactured in house
Made in the USA !
All Kits are CNC machined to order
Ships lightly assembled
Original (Experienced) designer and creator of the first USA drag bike to market.
Gen1 Track record on a 1S battery 2.5t motor was 1.78 ET on prep
GEN1,GEN2,GEN3 Pro-Drag Bike
3mm satin black composite material
-Wheelbase 11.6" Total Length from front wheel axle to wheelie bar wheel axle, just a hair under 20"
-1/2" OD larger rear axle bearing.
- Aluminum rear axle
-2 Split design with integrated wheelie bar (easy to remove rear tire from just taking rear half off.
-Rock solid frame no twist or tweak design
-Adjustable wheelie bar system W/Rubber dual bearing Wheels
-Designed for up to 2.50" - 3.25"Dia" rear Wheel (1/10 pan car hub mount foam type or rubber)
-Wider and longer wheelbase than gen1 and gen2 versions
-Belt drive system configured for 132ft drag racing
2s battery shorty up to 96" in length and 26.5mm in height will fit.
- Fits 1/8 scale ESC such as fantom racing FR-8 Pro and other manufacture ones within a 60mmx45mm foot print. Super low center of gravity placement.
-Set up for- Any 1/10 35mm can motor size.Wide range of adjustment slots.
-Servo set up for push and pivot steering.
-Interlocking design panel lock into side rails with tabs for no flex / Twist.
- Rear ladder bar deck plate interlocks via slot/tab and nut and bolt.
-Dual CF bearing glide Triple tree with shoulder screw pivot
-39 degree Fork rake with CF forks and dual triple trees with bearing swivel
-Has a 45 degree from straight to left and right turn radius (Set your end points to best turn radius. RC bikes cannot turn hard or sharp turns.
- Servo position mounting plates ( 2 options on servo plates )
Comes in Kit form some assembly required
Required to complete and important info :
Motor - 1/10 Modified 3.5T and up
Some Motor shafts you will need shorten and or file or dremel flat spot on shaft more towards the motor bearing so to get proper pulley belt alignment. You may also use motor Spacers behind motor and carbon fiber frame rail will also bring motor out for either balancing or pulley alignment.
Servo arms - Aluminum arm BEST but plastic type is fine.
NOTE : When running belt drive be sure to check motor direction. Depending on which side you choose to have it on ( Normal direction is having belt on left side when looking at bike from rear) If you need to Reverse the motor direction that can be done by esc setting or radio, check radio and esc manual before doing operating.Most motors is recommend to set timing to "0" if running in reverse as when reversing direction turns + timing into - visa ,versa
Battery -2S Shorty- Suggesting for example - Fantom Racing 6100mAh, 130C, 7.6v, 2-Cell, SHORTY, MVS 2.0 PRO HV Silicon Graphene LiPo-HV
Rear Foam Tire / Rim pan car bolt pattern 2 or 4 bolt-
Size up to 3.25" Tall x up to 2" wide.Best to use tire truer to do truing and trimming of heights to adjust gear ratio for 132ft .RC4WD has alum 2" front and rear drag rims call components. store.rc4wd.com/search.asp?keyword=drag+ri+
For front drag rim rubber tire here is link to O ring style above for foam for rear see below.
(rear rim requires own foaming by user or send to gone bananas racing skinz for foaming), TM rc racing x compound http://tmrcracing.com/1-10th-Scale_c26.htm or BSR pink compound at Your Battery Buddy at www.yourbatterybuddy.com/index.php/wheels-and-tires/foam-wheels-tire/bsr-racing-foam-tires-wheels/bsr-1-10-scale-tires/bsr-1-10-foam-tires-and-wheels-pink-duro-30-35-1-75-x-2-75-1-10-scale.html
Gone Bananas racing skinz to name a few. You can true your heights lower as needed to dial in your ET and MPH also 6ft times better.
1/10 ESC or as large as 1/8 scale ESC- Suggestions like -1/10 Tekin RS Pro Black
Fantpom racing FR10 PRO OR FR8 PRO.
Servo - Micro
Designed and sized for a Savox micro servo 21T Spline 6.6v SH-0265MG digital Dimensions: L 22.8 x W12 x H27.5 mm & 20.3mm. Under mount tabs to bottom of servo. (Under servo mount tabs to battery if using suggested of servo max length you have is 22.5mm
MKS93i hv handles 6.6v,7.4v or 8.4v Dimension: 23x12x27.25 mm.
Suggested amazon listing - BQLZR Metal 21T Servo Horn Arm TL2366 Silver Replacement for Hengji 922 933
These are just suggestions different brand servos may use a certain spline size some sure to check.
Or any other micro servo with same or slightly smaller sizing.Some servos have single mounting hole others have 2 so pay attention
You can always use spacers under screw tabs to position servo how you like to align heights.
Servo mount plate opening dimensions : 24.5mm Long (front to back viewing) 13.5mm wide (side to side) mount hole center to center distance 29mm (This may vary based on tolerances of cnc machining)
Rear axle mount hub not included (Please get from here) 1/10 pan style 1/4" hub or can use 1/2" hub pan style 1/10
Note: This is a A to B Drag bike for smooth clean surface roads of either prepped or non prep drag tracks or street. You must slow way down to turn around. Concrete is best surface unless you find a good asphalt surface. koford foam tire traction heavy compound will give best results on no prep foams.
When pressing in rear axle bearings onto side rails upon assembly dont force it tap in evenly.Most times it will snap in place.